Brands Vehicles
Lowest Prices
Free Returns
Online Since 2009
Shopping for

1998 Pontiac Grand Prix

X

ACDelco 251-2060 Engine Coolant Outlet Gasket
for 1998 Pontiac Grand Prix

ACDelco 251-2060 Engine Coolant Outlet Gasket - 1998 Pontiac Grand Prix Image 1
ACDelco 251-2060 Engine Coolant Outlet Gasket - 1998 Pontiac Grand Prix Image 2
ACDelco 251-2060 Engine Coolant Outlet Gasket - 1998 Pontiac Grand Prix

ACDelco
Brand:ACDelco
Part Number: 251-2060
UPC: 00707773849552
Weight: 0.05 lbs
Condition:New



Availability:
0 in Stock
 OUT OF STOCK

Product Information

Description:

Get the ACDelco 251-2060 Engine Coolant Outlet Gasket for your 1998 Pontiac Grand Prix. Buy now and secure your purchase online!

GM Genuine Parts Engine Coolant Outlet Gaskets are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These gaskets are used between the engine coolant outlet housing and the engine block or another component to seal the interface between the components. The engine coolant outlet gasket may be made of fiber or a rubberized composite material that provides a liquid-tight connection. The gasket keeps the engine coolant in and keeps air out. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE). ⚠ WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov

Features and Benefits:

  • GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
  • GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
  • GM regularly updates production and service part designs to integrate new materials and technologies
  • May be made from fiber or a rubberized composite material
  • Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)

Specifications:

Center Bore Diameter (mm):
38mm
Color:
Gray
Height (in):
2.04 in
Length (in):
4.2 in
Material:
Reinforced Fiber
Mount Hole Diameter (mm):
8.4mm
Mount Hole Quantity:
2
Thickness:
0.036 in.
Thickness:
0.91 mm
Weight (lb):
0.05 lb
Width (in):
2.44 in

Features and Benefits:

  • – A stain around the weep hole is acceptable. However, if a weep occurs with the engine running and the coolant system pressurized, then the water pump should be replaced.
  • – After installation, pressure-test the system for leaks and check for sufficient fan blade clearance between the blade and radiator shroud.
  • – Clean all excess dirt and debris from the water pump housing.
  • – Clean all sealing surfaces, and make sure all old gasket material is removed before installing your replacement component.
  • – Clean and reinstall the coolant recovery reservoir before flushing the cooling system.
  • – Do not use any non-approved flush agents and replace the coolant according to manufacturer's specifications.
  • – Flush the cooling system completely, using power flush equipment or thermal cycling the system with clean water three times. The most effective method of system flushing is to use a coolant exchanger, following the manufacturer's operating instructions.
  • – Inspect for leakage at the water pump outlet housing or the rear cover gasket, and leakage at the water pump vent or weep hole.
  • – Inspect related components in the cooling system, including your fan blades, fan clutch, engine mounts, radiator, belts and hoses, and reservoir.
  • – Never strike the water pump shaft, since this will damage the new water pump.
  • – Run your vehicle to increase engine temperature, and ensure the system is pressurized.
  • – Torque all bolts according to the manufacturer's specifications and adjust belts to proper tension (if applicable) to manufacturer's specifications.
  • – Use sealant tabs only if recommended. Some sealant tabs or similar compounds may restrict coolant flow through the passages of some cooling systems.
  • – With the new pump installed, turn the hub by hand and check for rotation.
  • Before purchasing and installing an engine coolant outlet gasket, make sure it is the correct fit for your vehicle.
  • Tips for Water Pump Inspection:
  • Tips for Water Pump Servicing & Installation:

Specifications:

Country of Origin:
US

ACDelco 251-2060 Engine Coolant Outlet Gasket compatibility with your 1998 Pontiac Grand Prix...

Last Updated: 03/01/2024

Years Vehicle Per Vehicle Fit NotesFitment Notes

1998

 

1997

 

1998

 

1997

 
Pontiac Grand Prix

3.8L V6 Gas OHV
1
 
Eng: L36
8th VIN Digit: K
 

Pontiac Grand Prix



3.8L V6 Gas OHV Eng: L36
8th VIN Digit: K

1 Per Vehicle

1998

 

1997

 

1998

 

1997

 
Pontiac Grand Prix

3.8L V6 Gas OHV Supercharged
1
 
Eng: L67
8th VIN Digit: 1
 

Pontiac Grand Prix



3.8L V6 Gas OHV Supercharged Eng: L67
8th VIN Digit: 1

1 Per Vehicle

Didn't find a match for your vehicle?

  See Other Choices